Submitting Files For Print
TIPS FOR QUALITY OUTPUT
We want to provide you with the best possible print products, we request that all files be sent using these standard formats. We request that any files dependent on the native application, fonts, or other separate design elements used to create the pieces be sent in the following formats:
TIF – JPG – PDF – EPS – PSD
We can use Quark, Pagemaker, Corel Draw, or any similar files by converting them to the above formats. Keep in mind, however, that any design elements dependent on the native application or computer, such as fonts that are installed on your computer but not in the Limitless Print system, may be lost in this process. (See below for more information on fonts.) Instructions on how to convert are included below.
What to know before you submit . . .
Please take the time to review all of this carefully! Although we take our time to insure each file is set-up properly and that we are representing your digital file in print correctly, we are not responsible for the quality of the artwork that you submit. To insure proper output, please follow all guidelines. If you have any questions regarding files, please don’t hesitate to reach out to our customer service department.
We are a high resolution printer, so we require all submitted files to be 300dpi (Dots Per Inch). If you design a file at 72dpi or lower, we cannot use the file. Our pre-press system would resize image to 300dpi, therefore “stretching” it out and lowering the quality. In the example on the right, one image was created at 300dpi, the other was created at 72dpi and then stretched out to 300dpi.
(small format only – flyers, postcards, postcards, business cards, etc.)
About 1/8” on all sides will be trimmed off. Everything that extends past the original canvas size is considered a “bleed.” Make sure you do not have any important content in this area. Adjust your canvas size to compensate for this; and an additional 1/8″ on all sides. (See Size)
bleed graphic Although our cutting staff is extremely precise, we can not guarantee any print job cuts without the added bleed. There are no exceptions. Also, please keep your text at least 1/4″ away from the edge of the piece unless it is an eighth of a page or smaller. This way your text is in a “safe” area. If you have any questions regarding this policy you may call us.
(small format only)
The trim area is a space of 1/8″ after the bleed. Its purpose is to separate any text or important content from the edge.
(small format only)
The safety area is the space where its “safe” to put your layout, design and content. This is usually 1/4″ from the edge of the canvas. On smaller projects, such as business cards, you can design closer to the edge.
Your print files should be designed in the size that is being ordered. We assume that you desire what you have ordered, and files will be re-sized in accordance to the job. We will not stretch and enlarge a file unless at your request. For example, a 4.25″ x 5.5″ design ordered as a 4″ x 6″ postcard print would have to be manipulated in order to print edge to edge and not have content cut off.
If your job requires a border, please note that in order to have your border exact, we recommend AT LEAST a minimum of 1/4″ on all sides. Our cutters are specialists in their field. Due to paper shift, however, borders cannot be cut to be exactly balanced on all sides. The thinner the border, the more that small differences will show. For more information on printing with borders.
There are two types of color spaces that are used for graphic and print design:
RGB (Red, Green, Blue): These are the colors your monitor uses to display everything.
CMYK (Cyan, Magenta, Yellow, Black): These are the colors used for printing.
Color shifts are usually not visible in color photographs; however, rich and solid colors (like a background) can be affected by a color conversion. Most of the time, color shifts are minor and will not be noticeable. But sometimes they will.
Limitless Print can get nearly any font in existence, but we may not have the font that you used in your design currently installed in our system. If you submit a PSD, AI, PDF, or TIF file, fonts that we don’t have may be replaced with different fonts.
There are several ways to avoid this happening. The easiest way is to submit a JPG file. This will embed the type into your design. (If you do submit a JPG, please make sure that your design is completely print-ready, as we will have very little ability to make corrections to this type of file.) You can also simply tell us the specific names of the fonts that you used and, if we don’t have them, we will get them.
If you have designed using Adobe Photoshop or Illustrator, another method is to rasterize or “create-outlines” for your type.